• Instant and fast hardware scanning. How to use driver pack autorun download bleeping. • Detection and diagnostic of hardware failure.

Thank you for your recent purchase of an Evinrude E-TEC outboard engine. Photographs and illustrations used in this Guide might not depict actual. 5 days ago - [Free Download] Evinrude Shop Manual Free Ebooks. Book file PDF easily for everyone and every device. You can download and read online.

This Johnson Evinrude Repair Manual 1958 to 1972 is a 525-page service manual in PDF format. The repair manual covers 958 to 1972 Johnson and Evinrude engines as follows: • 50 hp to 125 hp outboard motors. • 3 cylinder and 4 cylinder • Magneto • Engine repair info • Technical information. The entire manual is displayed below as a full readable PDF.

Free PDF service manual You can easily read and scroll through the pages all the pages in the repair manual PDF. The full manual is displayed on this web site for you you to read for free in your Internet web browser. If you want your own copy to browse locally on a smart phone (iOS or Android) or a tablet, such as an iPad or Android tablet device, then you can access the document for download from this link for an affordable one-time fee: What years are covered by this JohnSon Evinrude Repair Manual? This marine engine repair manual covers the outboard motors for the following years: 1958, 1959, 1960, 1961, 1962, 1963, 1964, 1965, 1966, 1967, 1968, 1969, 1970, 1971, 1972 Johnson Evinrude Marine Engine Repair (This PDF file is 525 pages so it will take a few seconds to a minute load. The faster your internet connection the shorter your wait.) Can I download this Johnson EvinRude Repair Manual as a PDF? If you want a copy of this manual to keep locally on your computer, mobile phone or tablet, you can download it for a fee as below. It is print quality, so you can print it on any desktop printer.

You can purchase the PDF download using the button below for a small one-time fee.

The Johnson-Evinrude Workshop manual downloads for the above listed models describes the service procedures for the complete vehicle. Follow the Maintenance Schedule recommendations to ensure that the outboard is in peak operating condition. Performing the scheduled maintenance is very important. It compensates for the initial wear that occurs during the life of the outboard motor.

All chapters in the Workshop Manual apply to the whole vehicle and illustrates procedures for removal/installation of components that are in detailed step-by-step fashion. Most all Workshop manual chapters start with an assembly or system illustration, diagrams, exploded parts view, pictures, service information and troubleshooting for the section. The subsequent pages give detailed procedures. PROBLEM 1: ENGINE TURNS OVER BUT WILL NOT START OR STARTS HARD WHEN COLD Possible Cause Corrective Action Improper starting procedure. Check procedure, as outlined in “Operation and Maintenance Manual.” Fuel tank empty; improperly mixed fuel; contaminants (water, dirt, etc.) in fuel. Check fuel in fuel tank and replace or add.

Fuel tank air vent closed or restricted. Air vent must be open and free from contaminants. A pinched or restricted fuel line. Check, and replace as needed. Dirty or restricted fuel filter.

Check, replace or clean. Enrichener valve not operating. Check enrichener system. (Refer to “Enrichener System” following.) An inlet needle (in carburetor) that is stuck open or closed. (A needle stuck open, will cause a flooding condition.

A needle stuck closed, will prevent fuel from entering carburetor.) Remove, clean, or replace. Anti-Siphon valve restricting fuel flow. Refer to “Checking for Restricted Fuel Flow caused by Anti-Siphon Valves”, following. See “Checking for Restricted Fuel Flow caused by Anti-Siphon Valves”, page 3A-1.

PROBLEM: ENGINE FLOODS Possible Cause Corrective Action Dirt or foreign particles are preventing inlet needle from seating. Flush out inlet seat and clean inlet needle.

Worn inlet needle. Punctured float. Incorrect float setting. PROBLEM: ENGINE RUNS TOO LEAN Possible Cause Corrective Action Carburetor is loose.

Air leaks past mixing chamber cover. Tighten bolts securely. Tighten cover or replace gasket. Fuel level too low. Reset float level. Clogged high speed jet. Check and clean.

Restricted fuel flow to carburetor. Check fuel lines and filter(s) for restricted flow. Incorrect high speed jet. Refer to main jet chart and replace with proper jet. Idle mixture set too lean.